Quick answer
Clean the lint screen with every load, wash it every few weeks, wipe the drum and door seal weekly, and clean the exhaust vent at least once a year, or sooner if a load takes longer than one cycle to dry. A clogged vent is the leading cause of dryer fires, so the vent matters more than the drum.
Most people clean one part of their dryer: the lint screen. It's the part you see every time you do laundry, so it gets the attention. The vent, the drum, the lint trap housing and the seal around the door get cleaned far less often, and the vent in particular is what causes problems, both for how well your dryer works and for fire safety. This guide goes through every part in the order that makes the most difference.
What you need
- A vacuum with a hose and a crevice attachment
- A flexible vent brush (sold at most hardware stores)
- A long, narrow lint brush or a lint trap brush
- A damp microfiber cloth and a dry one
- Dish soap and an old toothbrush for the lint screen
- A screwdriver, if your vent connection is clamped
- Gloves and a dust mask, since vent lint is fine and dusty
How often to clean each part
- Every load: the lint screen. The U.S. Fire Administration recommends cleaning the filter before and after each cycle, and never running the dryer without it.
- Every few weeks: wash the lint screen with soap and water to remove the film left by dryer sheets and fabric softener.
- Weekly to monthly: wipe the drum and the door seal, and vacuum the lint trap housing.
- At least once a year: clean the exhaust vent from the dryer to the outside, or more often if drying is taking longer than normal, according to the NFPA.
- Whenever you move the dryer: check that the vent hose behind it is not crushed, kinked or damaged.
Step 1: clean the lint screen properly
- Remove the lint screen and pull off the visible lint by hand.
- Every few weeks, wash it with warm water and dish soap and scrub the mesh gently with a soft toothbrush. This clears the invisible film that builds up from dryer sheets and fabric softener. The film is what makes the screen feel waxy, and it is often why a dryer starts taking longer to dry.
- Test it: run a little water over the dry mesh. If the water sits on top in beads or a sheet instead of passing through, there's still film blocking the airflow, so scrub it again.
- Let it dry completely before putting it back in.
Using fewer dryer sheets, or none, means less film builds up on the screen in the first place.
Step 2: vacuum the lint trap housing
Lint doesn't only collect on the screen. It also falls into the slot the screen sits in, and from there it heads toward the vent.
- Shine a flashlight into the lint trap slot to see how much is down there.
- Push the vacuum's crevice attachment or a lint trap brush into the slot and pull out what you can reach.
- Wipe around the opening with a damp cloth, then dry it.
Step 3: clean the exhaust vent (dryer vent lint removal)
This is the step that matters most and gets skipped the most.
- Unplug the dryer and pull it away from the wall. If it's a gas dryer, don't disturb the gas line, and see the gas dryer section below.
- Disconnect the vent hose from the back of the dryer.
- Vacuum the dryer's exhaust port and the inside of the hose with a hose attachment.
- Push a vent brush through the hose and the wall duct to break up lint further in, then vacuum again.
- Go outside and clear the exterior vent cover. Make sure the flap opens and closes freely and isn't blocked by debris, snow or a bird's nest. The NFPA and the USFA both stress that the outdoor flap has to open when the dryer is running.
- Reconnect everything and plug the dryer back in.
If your vent runs a long distance, has several turns, or goes through the roof, it's safer to have a professional clean it than to reach into ductwork you can't fully see.
Dryer vent lint removal: pick your method
There is more than one way to get lint out of a vent. Choose by how long and how straight your vent run is.
- Vacuum and vent brush (short, straight runs). Disconnect the hose, vacuum the exhaust port and the hose, then push a flexible vent brush into the wall duct a short length at a time. If it snags, pull it back a few inches instead of forcing it, then vacuum the loosened lint out from both ends.
- Vent brush on a drill (longer runs). Some brush kits connect to a drill so the brush spins as it goes in. Use the slowest setting and follow the kit's directions, and stop if the brush jams.
- A dryer lint removal service (long runs, many turns, roof vents). The NFPA says the vent pipe can be cleaned by you or by a dryer lint removal service, so a long or twisting run is a good reason to hire one.
Whichever you pick, finish at the outdoor cover: clear the flap and the opening, then check that it opens fully while the dryer runs.
A five-minute check: is your dryer vent clogged?
- Run the dryer on a heated cycle with a small load, or an empty drum.
- Go outside and look at the vent cover. The flap should open fully and stay open while the dryer runs, which is what the NFPA and the USFA both stress.
- Hold your hand near the opening. You should feel a steady stream of warm air. A weak trickle, or none at all, means the vent is restricted.
- Look at the hose behind the dryer. It should not be crushed, kinked or packed with lint.
If the flap barely moves or the air is weak, clean the vent before the next load. A blocked vent also makes the dryer work harder, which is why a load starts taking two cycles to dry.
The vent hose: material and shape matter
Cleaning only works if the vent itself is in good shape.
- Use metal. The NFPA says rigid or flexible metal venting should be used to keep airflow and drying time right. Thin plastic or vinyl hoses crush and sag easily, and lint catches in the dips.
- Check that it isn't damaged, crushed or restricted. The USFA recommends checking the venting behind the dryer, and a hose squashed between the dryer and the wall is a common problem.
- Keep it short and straight where you can. Every bend slows the air and gives lint a place to settle.
- Don't vent into the house, a garage or an attic. The air should go outside.
Step 4: wipe the drum and door seal
- Wipe the inside of the drum with a damp cloth to remove residue from dryer sheets and fabric softener, which can transfer onto light-colored clothes.
- For sticky buildup, use a cloth dampened with a little dish soap and water, then wipe again with a clean, damp cloth and dry it.
- Wipe along the rubber door seal, where lint and residue collect and are easy to miss.
- Check the manual before using any other cleaner, and never mix cleaning products. Run the dryer empty on a short cycle afterward so any remaining moisture is gone before the next load.
If your dryer has moisture sensor strips (two small metal bars inside the drum), many manufacturers suggest wiping them occasionally with a cloth and a little rubbing alcohol, since film can stop them from reading the load properly. Check your manual to see if yours has them.
Step 5: clean behind and around the dryer
The USFA specifically says not to forget the back of the dryer, where lint builds up. Vacuum behind and underneath the machine and wipe the top and front with a damp cloth. The NFPA also advises keeping the area around the dryer clear of things that can burn, like boxes, cleaning supplies and clothing, so don't use the space behind or beside it for storage.
Signs your dryer needs cleaning now
- A load takes two cycles to dry that used to take one
- The outside of the dryer feels hot to the touch during a cycle
- Clothes come out hotter than usual or smell faintly burnt
- You notice lint around the back of the dryer or the outside vent cover
- The outdoor vent flap barely moves, or doesn't open at all, while the dryer runs
- Laundry feels damp and your room gets humid when the dryer is on
Any of these point to restricted airflow, which is the vent, the screen, or both. If you smell something burning, stop the dryer, unplug it and let it cool, and don't use it again until the screen and vent are checked. If you ever see smoke or flames, get everyone out and call 911.
Gas dryers and installation
Both the NFPA and the USFA advise having your dryer installed and serviced by a professional, and the NFPA says gas dryers should be inspected by a qualified professional to make sure the gas line and connection are intact and free of leaks. Don't disconnect or move a gas dryer's gas line yourself. Also make sure the dryer is plugged into the right outlet and properly grounded, as the NFPA recommends.
What not to put in the dryer, and other safe habits
- Clothes with flammable substances. The NFPA says clothes that have touched gasoline, paint thinner or similar solvents should be laid outside to dry first, then washed and dried as usual.
- Overloaded loads. Follow the manufacturer's instructions and don't overload the dryer, which blocks airflow and strains the machine.
- Running it while you're out or asleep. The NFPA advises turning the dryer off if you leave home or when you go to bed.
- Running it without the lint screen. Never do this.
What if it still takes forever after cleaning?
If the vent and screen are clear and clothes are still damp, check these in order: the load size (too big for the drum), the washer's spin speed (clothes that come out dripping take far longer, and a clean washing machine drains better), the heat setting, and the outdoor flap one more time. If none of that helps, a technician can check the heating element, the sensors and the venting run you can't see.
Why this is more than a cleaning chore
Dryer lint is highly flammable, and a blocked vent is one of the most common causes of home dryer fires. The NFPA puts it bluntly: the leading cause of home clothes dryer fires is failure to clean them. Treat the vent cleaning step as a safety task, not an optional deep clean. If you're setting up a whole laundry area, our laundry room organization guide shows how to leave room to pull the dryer out for vent cleaning, and our guide to cleaning pillows covers drying bulky items on low heat.
Sources
- U.S. Consumer Product Safety Commission, Clothes Dryer Fires fact sheet
- U.S. Fire Administration, Clothes Dryer Fire Safety
- National Fire Protection Association, Clothes Dryer Safety tip sheet
Frequently asked questions
How often should I clean my dryer vent?
The NFPA says to clean lint out of the vent pipe at least once a year, or more often if clothes are taking longer than normal to dry, or to have a dryer lint removal service do it. Clean the lint screen with every load, not just the vent.
Why does my dryer take more than one cycle to dry clothes?
A dryer that needs two cycles to dry a normal load is usually a sign of restricted airflow, most often a clogged vent or lint screen. Clean both, check that the outdoor vent flap opens, and make sure the load isn't too big before assuming the dryer itself is failing.
Can I clean a dryer vent myself?
You can clean the parts you can reach: the lint screen, the lint trap housing, the vent hose behind the dryer and the outside vent cover, using a vacuum and a vent brush. A vent that runs a long distance, has several turns or goes through the roof is safer left to a professional.
Is dryer lint actually a fire hazard?
Yes. The U.S. Consumer Product Safety Commission links lint buildup in the dryer vent to a significant share of the roughly 15,500 dryer fires reported each year in the United States, and the NFPA says the leading cause of home clothes dryer fires is failure to clean them.
What is the best material for a dryer vent?
The NFPA says rigid or flexible metal venting should be used to keep airflow and drying time right. Thin plastic or vinyl hoses crush and sag easily, which is how lint gets trapped, so a metal vent that is not crushed or kinked is the safer choice.
Can I dry clothes that have gasoline or paint thinner on them?
The NFPA says clothes that have come in contact with flammable substances like gasoline, paint thinner or similar solvents should be laid outside to dry first. After that they can be washed and dried as usual.
Is it safe to run the dryer when I'm not home?
The NFPA advises turning the dryer off when you leave home or go to bed. Finish the load while you are there, so any problem is noticed early.
How do I remove lint from a dryer vent?
Unplug the dryer, pull it away from the wall and disconnect the vent hose. Vacuum the dryer's exhaust port and the hose, push a vent brush through the hose and the wall duct a short length at a time, then vacuum again. Clear the outdoor vent cover and check that the flap opens freely, and let a professional handle a long, twisting or roof-mounted run.
How do I know if my dryer vent is clogged?
The usual signs are loads that need two cycles, a dryer that feels hot on the outside, clothes that come out hotter than normal or smell faintly burnt, lint around the back of the dryer, and an outdoor flap that barely opens while the dryer runs. Any of these points to restricted airflow.
Can I clean a dryer vent with just a vacuum?
A vacuum with a hose attachment clears the dryer's exhaust port, the hose behind the machine and the outdoor vent opening. For lint packed further into the wall duct, a vent brush loosens it first and the vacuum then pulls it out. If the run is long or has many turns, use a professional.
This site may earn a commission from products linked here, at no extra cost to you.


