Quick answer
Test every strand on the ground first and throw out any with cracked sockets, frayed or bare wires, or loose connections. Use only lights labeled for outdoor use outside, plugged into a GFCI-protected outlet, and read the manufacturer's limit for how many strands can be connected. Set a ladder at the 4:1 angle (about 75°) with three points of contact, and turn the lights off when you go to bed or leave the house.
Lights are the part of holiday decorating that people rush, and it is also where the safety advice is most specific. This guide follows the U.S. Consumer Product Safety Commission (CPSC), the U.S. Fire Administration (USFA) and Washington State Labor & Industries. Where there is no official rule, such as how to start wrapping a tree, we say it is our own suggestion.
Why it is worth doing carefully
The USFA, citing the National Fire Protection Association, says almost one-third of home Christmas tree fires are caused by electrical problems. And the CPSC reported in a December 2017 release that about 14,700 holiday decorating injuries were treated in emergency rooms the previous season, roughly 240 a day across November and December, with falls the most frequent incident at 41%.
Step 1: Test and sort on the ground
- Plug in every strand before you hang it. This is our suggestion, and it saves you from finding a dead section when you are already on a ladder.
- Check each set, new or old. The CPSC says to look for broken or cracked sockets, frayed or bare wires, and loose connections, and to throw out damaged sets. The USFA says the same for strands with frayed or pinched wires.
- Look for a testing-lab label. The CPSC says to use only lights tested for safety by a nationally recognized testing laboratory. In 2009 it gave UL and ETL as examples, and advised newer lights with thicker wiring and safety fuses to keep the wires from overheating.
- Sort by where each strand will go. Indoor-only strands stay indoors; outdoor strands need a label showing they are certified for outdoor use.
Step 2: Plan your plugs and strand count
- Read the manufacturer's limit. The USFA says to read the instructions for the number of light strands to connect. It is usually printed on the tag or the plug, and it changes by type of light, so check each box.
- Pick the cord for the job. The CPSC says to check that each extension cord is rated for the intended use and in good condition, and not to use cords with cuts or signs of fraying.
- Measure before you buy. This is a rule of thumb from retailers, not a standard: many suggest about 100 mini lights per foot of tree height, and more for a fuller look. Our suggestion is to buy one extra strand to fill gaps.
- Think about where the plug will be. Draw the route from the outlet first, so no cord crosses a doorway or walkway.
Step 3: Hang lights on an indoor tree
Do this after the tree is stable and, if it is real, has water in the stand. Our guides to watering a Christmas tree and decorating it step by step cover those parts.
- Unplug the strand while you work. Plug it in only to check the effect.
- Start at the trunk end near the outlet. This is our suggestion: put the plug end where the cord can run to the outlet without stretching.
- Work from the bottom up and weave in and out. Laying the strand deeper along the branches and not only on the tips gives more depth. Step back every few rounds to check for gaps.
- Keep the tree away from heat. The USFA says to keep a tree at least 3 feet away from heat sources such as fireplaces, radiators and space heaters, and not to block exits.
- Skip electric lights on a metallic tree. The CPSC says faulty lights can electrify it.
Step 4: Hang lights outdoors
- Use outdoor-rated lights only. The CPSC says to check labels showing they are certified for outdoor use.
- Use a GFCI outlet. The CPSC says to plug outdoor lights only into a GFCI-protected receptacle or a portable GFCI.
- Use clips that fit the surface, not nails or staples. This is our suggestion, because a nail or staple can damage the wire. Clips made for gutters, shingles or trim are sold for this.
- Keep the strand loose. Our suggestion: let it follow the edge without being pulled tight, so wind and temperature changes do not stress the wire.
- Keep plugs and connections off wet ground. Again our suggestion; the sources above do not give a specific height.
Step 5: Use a ladder the safe way
The CPSC's figures above show why this step matters. Washington State Labor & Industries gives these ladder rules:
- Inspect first. Check the ladder before you set it up.
- Use the 4:1 rule. For every 4 feet of height, set the base 1 foot out from the structure, about a 75° angle.
- Reach past the edge. To get onto a roof or higher level, the top of the ladder must extend at least 3 feet past the edge.
- Make the feet stable. They must be on stable material and unable to slip out.
- Use three points of contact. Do not climb carrying an armful of lights; hang them from a bucket or a bag clipped at your waist. That last part is our suggestion.
- Never stand on the top step or cap when the manufacturer prohibits it.
Our suggestion for the roofline: if the job is above the first story or you do not have a second person to steady the ladder, skip it and light the porch, railings and bushes instead.
Step 6: Run them safely
- Turn lights off at bedtime and when you leave. The CPSC says they could short out and start a fire.
- Use a timer. A plug-in outdoor timer makes that automatic. It is our suggestion, and it should be rated for outdoor use if it sits outside.
- Recheck after wind or snow. If a strand has come loose or the cord is damaged, unplug it and fix or replace it.
- Plan the take-down. When the season ends, our guide to storing Christmas decorations shows how to check and wind them for next year.
Quick checklist
- Every strand tested on the ground and damaged ones thrown out
- Outdoor strands labeled for outdoor use, in a GFCI outlet
- Strand limit on each box read and followed
- Extension cords rated for the job, with no cuts or fraying
- Ladder inspected, set at 4:1, extended 3 feet past the edge, with three points of contact
- Tree at least 3 feet from heat and not blocking an exit
- Lights off at bedtime and when you leave
Mistakes to avoid
- Hanging a strand you have not tested
- Using indoor-only lights outside or indoor cords outdoors
- Connecting more strands than the manufacturer allows
- Putting electric lights on a metallic tree
- Climbing a ladder set too steep or too flat, or without three points of contact
- Leaving lights on overnight
Sources
- U.S. Consumer Product Safety Commission (CPSC), "Put Safety at the Top of Your List When Decorating this Holiday Season" (released Dec. 6, 2017)
- CPSC, "Do's and Don'ts of Holiday Decorating" (2009)
- U.S. Fire Administration, Holiday Fire Safety
- Washington State Department of Labor & Industries, Ladder Safety
Frequently asked questions
How do I check Christmas lights before I hang them?
The CPSC says to check each set of lights, new or old, for broken or cracked sockets, frayed or bare wires, or loose connections, and to throw out damaged sets. The U.S. Fire Administration (USFA) adds that you should inspect holiday lights each year before you put them up and throw away strands with frayed or pinched wires.
Can I use indoor lights outside?
No. The CPSC says to check outdoor lights for labels showing they have been certified for outdoor use, and to plug them only into a ground-fault circuit interrupter (GFCI) protected outlet or a portable GFCI.
How many strands of lights can I connect together?
Read the manufacturer's instructions, which the USFA says to do for the number of light strands to connect. The limit is usually printed on the tag or plug of each set, and it can differ between incandescent and LED strands, so we do not give one number here.
Should I leave Christmas lights on overnight?
The CPSC says to turn off all holiday lights when you go to bed or leave the house, because the lights could short out and start a fire. A plug-in timer is a convenient way to do this; that is our suggestion, not an agency rule.
How do I set up a ladder to hang lights?
Washington State Labor & Industries describes the 4:1 rule: for every 4 feet of height, set the base 1 foot out from the wall, which is about a 75° angle. The top should reach at least 3 feet past the edge of the roof or landing, the feet need stable footing, and you should keep three points of contact.
Can I put electric lights on a metallic tree?
The CPSC says not to use electric lights on a metallic tree, because faulty lights could electrify it.
This site may earn a commission from products linked here, at no extra cost to you.



