Quick answer

Scrub a baking soda and water paste into the grout lines weekly to prevent buildup. For stains, use hydrogen peroxide instead of bleach on colored grout, and never use vinegar on natural stone tile. Black mold needs hydrogen peroxide and, if it keeps returning, a fresh coat of sealer.

Tile stays clean with a quick wipe because it's a sealed, non-porous surface. Grout is the opposite — it's porous by nature, which is exactly why it grabs onto dirt, soap residue and moisture and holds on to them. A tile floor that looks dingy is almost never the tile. It's the grout lines between them.

What you need

Weekly upkeep

  1. Mix baking soda with a little water into a thick paste.
  2. Spread the paste along the grout lines with an old toothbrush or grout brush.
  3. Let it sit for 10 minutes.
  4. Scrub in small circles, then rinse with warm water.

Done weekly, this alone keeps most grout from turning grey or yellow in the first place.

Deep cleaning stained or dingy grout

  1. Spray 3% hydrogen peroxide directly onto the grout lines. It's a safer choice than bleach, since it won't discolor colored grout the way bleach can.
  2. Let it sit for 10 to 15 minutes so it has time to break down the stain.
  3. Scrub with a stiff grout brush, working along the line rather than across it so you don't push grime into the tile edges.
  4. Rinse thoroughly with warm water and a clean cloth.
  5. For stubborn spots, repeat rather than scrubbing harder — grout wears down with abrasive force over time.

A word on vinegar and natural stone

Vinegar is a go-to in a lot of cleaning guides, but it's the wrong choice for one common situation: natural stone tile. Marble, travertine, limestone and similar stones are calcium-based, and vinegar's acid etches and dulls them on contact — sometimes permanently. On ceramic or porcelain tile, vinegar is generally fine for the grout itself, but if you're not sure what your tile is, skip the vinegar and use hydrogen peroxide instead.

Getting black mold out of grout

Black or pink spots in grout, especially in a shower or around a tub, are usually mold or mildew feeding on trapped moisture.

  1. Spray 3% hydrogen peroxide directly on the affected grout.
  2. Let it sit for 10 minutes.
  3. Scrub with a stiff brush, focusing on the mold itself rather than the surrounding grout.
  4. Rinse and dry the area, then run the bathroom fan to clear remaining moisture.

If the mold comes back within a week or two of cleaning it, that's usually a sign the grout needs to be resealed, or that moisture isn't drying out properly — check that your exhaust fan is actually venting outside and not just into the attic.

Whitening grout that's gone grey

For grout that's uniformly grey or yellowed rather than stained in spots, a grout whitening pen (sold at most hardware stores) can restore the look without a full reseal. It paints a fresh white or colored coating directly onto clean, dry grout lines. Clean and fully dry the grout first — the pen won't adhere well over grime or moisture.

Should you seal grout?

Cement-based grout is porous and generally benefits from a sealer, which helps it resist staining and mildew going forward. Some pre-mixed and hybrid grouts come pre-sealed or don't need it at all, so check your grout type before buying a sealer. If your grout is cement-based and has never been sealed, plan to reseal it roughly once a year, or sooner in a shower that gets heavy daily use.

  1. Clean and fully dry the grout — sealing over dirt or moisture traps both underneath.
  2. Apply a penetrating grout sealer with a small brush or applicator, following the lines.
  3. Wipe away excess from the tile surface before it dries.
  4. Let it cure fully — usually 24 to 72 hours — before the area gets wet again.

Keeping grout clean for longer

Sources

Frequently asked questions

What is the best homemade grout cleaner?

A baking soda and water paste, scrubbed in with a stiff brush, handles most everyday grime. For deeper stains, add hydrogen peroxide to the paste or spray it straight on before scrubbing.

Can I use vinegar on grout?

Not on natural stone tile like marble, travertine or limestone, since the acid etches and dulls the surface. On ceramic or porcelain tile it's generally fine for the grout, but check your tile type first.

How do I get black mold out of grout?

Spray 3% hydrogen peroxide on the mold, let it sit 10 minutes, then scrub with a stiff brush. If it keeps returning quickly, the grout may need resealing or the area needs better ventilation.

Does grout need to be sealed?

Cement-based grout generally does, since sealing helps resist stains and mildew. Pre-mixed and some hybrid grouts are often sealed already or don't need it — check your grout type first.

This site may earn a commission from products linked here, at no extra cost to you.